Pink Noise
Press Play. Softer than white noise. Set a timer if you want a fade-out.
https://flxcode.com/pink-noise/
Flat: the same energy at every frequency. Bright and hissy.
Falls 3 dB per octave. Softer than white, closer to steady rain.
Falls 6 dB per octave. Deep and rumbly, closer to a distant waterfall.
Our own mix, not a standard: pink noise limited to about 100 Hz to 3 kHz, centred near 500 Hz.
This browser keeps the volume of web pages fixed. Use the volume buttons on your device.
Stopped
Starts quiet on purpose. Keep the speaker away from your ears, and well away from a baby's cot. Nothing is uploaded: the sound is made in your browser.
No sound?
- iPhone: check the ring/silent switch and the media volume.
- Check the system volume and which output is selected (speakers, headphones, Bluetooth).
- Bluetooth headphones switch to call mode while a microphone is open: sound becomes mono and dull.
- A mono audio setting in accessibility makes left and right sound the same. A web page can't detect it.
- Another tab or app may be using the audio. Close it and press Play again.
No ads. No account. Nothing you type or record is uploaded. We count page events with a daily code. Check it.
Problem or idea? Email us
What pink noise is
Pink noise falls 3 dB per octave, so every octave carries the same energy. That is closer to how we hear pitch than white noise is, and it sounds softer and fuller: a bit like steady rain or wind in leaves. It is made here with a filter on white noise (Paul Kellet's refined pink filter), which stays within a fraction of a dB of the 3 dB slope across the audible range.
White noise is flat and brighter. Brown noise falls 6 dB per octave and is deeper. Pink sits in the middle.
How pink noise sounds
Pink noise has hiss on top and weight underneath, with no single note standing out. Compared with white it loses the sharp edge, and compared with brown it keeps enough treble to stay clear on a small speaker. Many people describe it as a waterfall heard from a few metres away.
Pink noise in numbers
Power per hertz falls by a factor of 10 for every tenfold rise in frequency, which is 10 dB per decade. From 20 Hz to 20 kHz is almost exactly 10 octaves, or 30 third-octave bands, and in each band the level is the same. Draw it on a linear frequency axis and you see a falling line. Draw it on a log axis with octave bands and you see a flat one.
What people use it for
Audio engineers play pink noise through a speaker and read the room with a real-time analyser: a flat bar graph means a flat response, and each bump is a room mode or a speaker fault. Many people also use it to mask background sound while they sleep or work.
How to use the timer
Under Sleep timer pick 15, 30, 60 or 90 minutes, or 8 hours. Pressing Play starts the countdown, or it starts at once if the sound is already running. The level fades during the final 45 seconds. Tap Off to cancel. The page needs to stay open, but it keeps going with the screen dark.
Other colours
White noise, Brown noise, Green noise. All four are in the noise generator. To play an exact tone instead, use the tone generator.
FAQ
What is the difference between pink and white noise?
Slope. White noise is flat in power per hertz, pink falls 3 dB per octave. In practice pink has less hiss and more low-mid body. Play both and compare: the colour buttons switch without a break.
Does pink noise help sleep?
We make no health claim. Many people use it to cover background sound at night. If it helps you, fine. If it does not, stop. Keep the volume low either way.
Is the pink noise here exact?
It is measured: over 100 Hz to 10 kHz the generated sound has a slope within a fraction of a dB per octave of −3, and the level is matched to the other colours, so switching does not change the loudness.
Why does a spectrum analyser show pink noise sloping down?
An FFT plot uses equal steps in hertz, so the upper octaves get many more bins than the lower ones and the line tilts. An analyser with octave or third-octave bands groups the bins the way hearing does, and then pink noise reads flat. Both plots are correct.
How do I loop pink noise in another player?
Press "Save 60 s as WAV". The last 3 seconds are crossfaded into the start, so the file repeats without a seam in any player that can loop a track. Browsers can add a tiny pause at the loop point of a web audio element, which the file avoids.
More from FLXCode
Noise GeneratorNew
White, pink, brown and green noise with a sleep timer and fade-out. Plays with the screen off.
Tone GeneratorNew
Play any frequency from 1 Hz to 22 kHz. Sine, square, triangle or sawtooth.
Decibel MeterNew
Estimate how loud a place is in dB, with A-weighting, min, average, max and Leq. Calibrate it against a known level.
White NoiseNew
Play white noise now. Sleep timer with fade-out, plays with the screen off, save a 60 s WAV.