FLXCode Speaker Rattle Test

FLXCode apps

Appearance

Speaker Rattle Test

Find the frequency where a speaker, grille or shelf starts to rattle.

20 Hz

sub-bass

Stopped

The tone glides from 20 to 300 Hz in 90 seconds. When you hear a rattle, press Mark rattle. The page then helps you narrow it down.

Arrow keys step 1 Hz. Hold Shift for 5 Hz.

Start quiet. Low tones can hurt small speakers.

Low tones can damage small speakers. Keep the volume low and stop if it sounds strained.

The volume slider sets the level in the sound itself. How loud it is at your ear also depends on your device volume and speakers.

Nothing is uploaded: the sound is made in your browser.

No sound?
  • iPhone: check the ring/silent switch and the media volume.
  • Check the system volume and which output is selected (speakers, headphones, Bluetooth).
  • Bluetooth headphones switch to call mode while a microphone is open: sound becomes mono and dull.
  • A mono audio setting in accessibility makes left and right sound the same. A web page can't detect it.
  • Another tab or app may be using the audio. Close it and press Play again.

No ads. No account. Nothing you type or record is uploaded. We count page events with a daily code. Check it.

Problem or idea? Email us

How to use it

  1. Turn your device volume down. The test starts at 10%.
  2. Pick Left, Both or Right. Test one speaker at a time if you can.
  3. Press Play. The tone glides up from 20 Hz (or from where you last stopped). Listen for a buzz, tick or chatter.
  4. When you hear it, press Mark rattle. The glide holds as a steady tone and you get a band around that frequency.
  5. Answer the narrowing questions: "Louder rattle here" or "Gone". Three step sizes, 5, 2 and 1 Hz.
  6. Optional: press Repeat once and do it again. If both runs land within 5 Hz, the result holds.
  7. Copy the summary. Stop with the Stop button or Esc. An arrow key during the glide also pauses it, and the buttons and arrows step the tone by 1 or 5 Hz.

Speaker buzzing, crackling or humming?

A buzz at one note is a rattle, and this page finds it. Crackle that changes when you move the cable is a loose wire or a dirty terminal. A steady hum at 50 or 60 Hz is electrical: check it with the 60 Hz tone. If only one side misbehaves, use the left and right speaker test.

Rattle or port noise

SoundRattlePort noise
CharacterBuzz, tick, chatter or a dry vibration.Breathy chuff, whoosh or whistle.
Where it comes fromA part that moves: a screw, panel, grille or the cone.Air moving through the port of a bass-reflex cabinet.
Touch testChanges or stops when you press the part.Feels like wind at the port opening.
LevelOften present at low volume, at one narrow frequency.Grows with volume, mostly near the port tuning.

Typical causes

  • Loose screws on the driver, the grille or the back panel.
  • A loose panel, a shelf or an object standing on or next to the speaker.
  • A loose or touching speaker wire, or a loose terminal.
  • Cone damage: a torn or glued surround, or a voice coil that rubs. This one is usually harsh and constant over a wide range, and it does not go away when you press the cabinet.
  • Loose bracing or a gap in the cabinet seam, on older or cheap enclosures.
  • The room: a window, a door or a picture frame that vibrates at one note.

How to fix it

  1. Tighten the screws on the driver, grille and back panel.
  2. Pad the spot: a strip of foam or felt between the speaker and the shelf, or under loose panels.
  3. Move things away from the speaker, or move the speaker itself. Cups, plants and picture frames love 60 Hz.
  4. Free-air test: take the speaker off the shelf, hold it in your hands and play the same tone. If the rattle is gone, the shelf was the cause.
  5. Isolate it with a steady tone: set the Hz you marked, then press and release parts of the speaker while it plays. The rattle changes where the fault is.

Accuracy and limits

The page can't hear the rattle. It makes a clean sine tone and shows the frequency it asks your device to play. A speaker that can't reproduce a low note will play something else, usually a distorted higher tone. The glide covers 20 to 300 Hz only. For the full 20 Hz to 20 kHz range, left and right and phase, use the speaker test. For a steady tone at any frequency, use the tone generator. The frequency readout is not a measurement of your speaker.

The starting volume is 10%. A volume restored from your last visit is capped at 30%, and you can raise it again with the slider. The volume slider sets the level in the sound. How loud it is at your ear depends on your device volume and speakers.

How it works

One sine oscillator in the Web Audio API glides from the current frequency to 300 Hz on an exponential ramp, so every octave takes the same time. Pause holds the oscillator at the frequency it reached, and the step buttons move it with a 20 ms smoothing, so nothing clicks. Starting and stopping fade over 50 and 80 ms. Nothing is recorded or uploaded. We count events without cookies (details).

FAQ

Why does the glide go so slowly?

A rattle often starts and stops within a few hertz. At 90 seconds for the whole range, the tone moves about 0.6 Hz per second near 20 Hz and about 9 Hz per second near 300 Hz, so you have time to react. Mark it as soon as you hear it. The result is a band that allows for your reaction time, then you narrow it down.

Why can I hear almost nothing low on my phone?

Phone and laptop speakers give almost nothing below about 150 Hz. What you hear there is often distortion at higher frequencies, not the tone itself. A rattle you hear while the screen shows 25 Hz may really be the shelf or the room responding to a harmonic.

What do I do with the result?

Copy the summary or write the band down. Then play a steady tone in that band, touch or press parts of the speaker while it plays, and see where the rattle changes. A rattle that stops when you press on a panel points to that panel.

Why does my speaker buzz?

A buzz at one note is usually a rattle: a loose screw, grille, panel or object that vibrates at that frequency. Crackle that changes when you move the cable is a loose wire or terminal. A steady hum at 50 or 60 Hz that is there all the time is electrical, not a rattle. Check it with the 60 Hz tone page.

Why does my speaker hiss or buzz at high volume?

A buzz that appears only when you turn it up is usually the cone or a loose part being pushed harder, or the amplifier clipping. Run the glide at a low level first, then raise the volume a little at the frequency you marked. A steady hiss that is there at any volume, even with nothing playing, is electrical noise in the amp or the source, not a rattle.

My subwoofer rattles. Is that this?

Often yes. Subwoofers rattle at one note when a panel, a port cover or something on top of them vibrates. Glide from 20 Hz at a low level and mark the note. A chuffing or whistling sound that grows with volume is air in the port, which is a different problem.

What does the band mean?

While the tone glides, you need about 0.4 seconds to press Mark, so the real frequency is a few hertz away. The band shows that range. The narrowing steps (5, 2, then 1 Hz) shrink it to about ±1 Hz. If two runs land within 5 Hz of each other, the result is stable. It is a practical check, not a standard.

The rattle comes and goes when I move the frequency. Is it the page?

Probably not. The page plays one clean tone with no gaps or steps in it. A rattle that shows up at one frequency and goes away a few hertz higher or lower is usually the speaker, its case or something near it vibrating at that note. That is what this test is for: mark it and narrow the band.

Is this safe for my speakers?

At the starting level of 10 % it is a quiet test. Low tones at high volume can overheat a voice coil or push a cone past its limit. Keep the volume low, and stop if the sound turns harsh or strained.

Can the page hear the rattle for me?

No. It plays a tone and shows the frequency. It does not use the microphone, so you decide what is a rattle.

Does anything get uploaded?

No. The tone is generated in your browser. The result stays in the page and is cleared when you leave. We count events, like how often a tone was marked, without cookies.

More from FLXCode

Share Speaker Rattle Test