FLXCode Speaker Test

FLXCode apps

Appearance

Speaker Test

Check that both sides work, are the right way round and are wired in phase.

Step 1 of 3

Stopped

Each button plays three short bursts of noise. The lamps show the signal sent to each side. Do you hear it only on that side?

Use headphones? Start quiet.

Phone speakers are often mono, so Left and Right sound the same there. Use headphones for this step. The page can't detect a dead speaker, so listen.

Start quiet, turn up slowly. Nothing is uploaded: the sound is made in your browser.

No sound?
  • iPhone: check the ring/silent switch and the media volume.
  • Check the system volume and which output is selected (speakers, headphones, Bluetooth).
  • Bluetooth headphones switch to call mode while a microphone is open: sound becomes mono and dull.
  • A mono audio setting in accessibility makes left and right sound the same. A web page can't detect it.
  • Another tab or app may be using the audio. Close it and press Play again.

No ads. No account. Nothing you type or record is uploaded. We count page events with a daily code. Check it.

Problem or idea? Email us

Quick start

  1. Turn your device volume down. The test starts at 10%.
  2. Left / right: press Left, Right and Both. The matching side should light up and play. For a quicker check, use the left and right speaker test.
  3. Phase: play In phase, then Out of phase. In phase should sound centred and fuller.
  4. Sweep: play the 20-second sweep and listen for where sound starts, rattles or fades out. To find the exact frequency of a rattle, use the speaker rattle test.
  5. Press Sounds right or Something's wrong after each step. Stop at any time with the Stop button or Esc.

What you should hear

TestGoodProblem
LeftSound only on the left, three short bursts.Sound on the right, on both, or nothing.
RightSound only on the right.Sound on the left, on both, or nothing.
In phaseCentred, full, solid bass.Wide or hollow, bass missing.
Out of phaseWide, diffuse, thinner bass.Sounds the same as In phase, or better.
SweepSmooth rise, no rattles or buzz.Rattle, buzz, gaps or sudden drops.

Troubleshooting

  • Left and right are swapped: swap the cables or the earbuds. Check the balance setting in your system sound settings.
  • Only one side plays: check the balance slider, the cable and the plug. On a phone, turn off Mono audio in the accessibility settings.
  • Both sides play the same: Mono audio may be on, or you are using a single phone speaker.
  • Out of phase sounds better: one speaker has its + and - wires swapped. Reverse them on one speaker.
  • Bluetooth: the first second can be cut off while the link wakes up. Play again. Some Bluetooth modes mix to mono.
  • No sound on iPhone: check the ring/silent switch and the media volume.
  • Rattle in the sweep: a loose part, a speaker grille or a shelf. Note the frequency where it starts, or pin it down with the rattle test.

Accuracy and limits

This is a setup check, not a measurement. It does not do room calibration, loudness in dB, frequency response (that needs a microphone) or surround sound. The phase test is by ear, so it works best with two speakers placed in front of you or with headphones. The sweep ends at 20 kHz, or lower if your audio device runs at a low sample rate. For one steady frequency use the tone generator. Above 8 kHz the sweep is quieter, so its output stays at or below -20 dBFS. dBFS is the level in the file, not how loud it is at your ear. To check the other half of a headset, try the mic test.

How it works

The page makes one pink-noise buffer and plays it through the Web Audio API on one or both channels. For the out-of-phase test the right channel is multiplied by -1. Every burst fades in and out over 15 ms, so starting and stopping never clicks. The sweep is a sine tone with an exponential frequency ramp. Nothing is recorded or uploaded. We count events without cookies (details).

FAQ

How do I know if my speakers are in phase?

Play the in-phase and out-of-phase buttons. In phase, the noise sounds centred, full and solid. Out of phase, it sounds wide, hollow or inside your head, with thin bass. If the two are the other way round, one speaker has its + and - wires swapped.

Why do Left and Right sound the same on my phone?

Most phones have one speaker, or two that play the same signal. Plug in headphones to check the two sides.

What is the sweep for?

It shows where a speaker starts to produce sound at the low end, where it rattles or buzzes, and where you stop hearing it at the top. Small speakers give up well above 20 Hz, and most adults stop hearing somewhere above 15 kHz.

Is this a calibrated test?

No. The volume is not in dB, and your device is not measured. It tells you whether the setup works, not how accurate it is. The Left and Right lamps show the signal the page sends to each side. They cannot tell you whether a speaker is dead, so use your ears.

Why does it use pink noise?

Pink noise has equal energy in each octave, so it sounds even and is easy to place in the room. A pure tone is harder to locate, and bursts of noise make left and right obvious.

Does anything get uploaded?

No. The sound is generated in your browser. We count events, like which test you played, without cookies.

More from FLXCode

Share Speaker Test